Cutting data calculation This table can be used for cutters with cutting edge angle = 45º ae/DC % Feed Per Tooth, mm/tooth (fz) 0,03 0,06 0,08 0,10 0,15 0,20 0,25 0,30 0,40 0,50 0,60 0,80 1,00 Speed Factor Average Chip Thickness, mm/tooth (hm) Width of cut up to and including DC/2 2 (0.02) 0,01 0,02 0,02 0,03 0,04 0,05 0,06 0,08 0,10 1.8 3 (0.03) 0,01 0,02 0,02 0,03 0,04 0,05 0,06 0,07 0,10 0,12 1.7 5 (0.05) 0,01 0,02 0,02 0,03 0,04 0,05 0,06 0,08 0,09 0,13 0,16 1.6 10 (0.10) 0,01 0,02 0,02 0,03 0,04 0,05 0,07 0,09 0,11 0,13 0,18 0,22 1.5 15 (0.15) 0,008 0,02 0,02 0,03 0,04 0,05 0,07 0,08 0,11 0,13 0,16 0,21 1.4 20 (0.20) 0,009 0,02 0,02 0,03 0,05 0,06 0,08 0,09 0,12 0,15 0,18 1.35 30 (0.30) 0,011 0,02 0,03 0,04 0,05 0,07 0,09 0,11 0,15 0,18 0,22 1.3 40 (0.40) 0,012 0,02 0,03 0,04 0,06 0,08 0,10 0,12 0,17 0,21 1.25 50 (0.50) 0,01 0,03 0,04 0,05 0,07 0,09 0,11 0,14 0,18 0,23 1.2 Face milling full engagement (Width of cut = DC) 100 (1.00) 0,02 0,04 0,05 0,06 0,10 0,13 0,16 0,19 0,25 0,32 1.0 Calculation of feed per tooth and cutting speed for side milling operations When using side milling it is necessary to increase the feed per tooth to keep the chip thickness at the same value. It is also possible to increase the cutting speed and keep the same tool life. Use the tables below. This table can be used for cutters with cutting edge angle = 60º ae/DC % Feed Per Tooth, mm/tooth (fz) 0,03 0,06 0,08 0,10 0,15 0,20 0,25 0,30 0,40 0,50 0,60 0,80 1,00 Speed Factor Average Chip Thickness, mm/tooth (hm) Width of cut up to and including DC/2 2 (0.02) 0,02 0,02 0,03 0,04 0,05 0,06 0,07 0,10 0,12 1.8 3 (0.03) 0,01 0,02 0,03 0,04 0,04 0,06 0,07 0,09 0,12 0,15 1.7 5 (0.05) 0,02 0,02 0,03 0,04 0,05 0,06 0,08 0,10 0,12 0,15 0,19 1.6 10 (0.10) 0,02 0,02 0,03 0,04 0,05 0,07 0,08 0,11 0,13 0,16 0,22 0,27 1.5 15 (0.15) 0,010 0,02 0,03 0,03 0,05 0,07 0,08 0,10 0,13 0,16 0,20 0,26 1.4 20 (0.20) 0,011 0,02 0,03 0,04 0,06 0,07 0,09 0,11 0,15 0,19 0,22 1.35 30 (0.30) 0,013 0,03 0,04 0,04 0,07 0,08 0,11 0,13 0,18 0,22 0,27 1.3 40 (0.40) 0,015 0,03 0,04 0,05 0,08 0,10 0,13 0,15 0,20 0,25 1.25 50 (0.50) 0,02 0,03 0,04 0,06 0,08 0,11 0,14 0,17 0,22 0,28 1.2 Face milling full engagement (Width of cut = DC) 100 (1.00) 0,02 0,04 0,05 0,06 0,10 0,13 0,16 0,19 0,25 0,32 1.0 Instead of using the table above for calculating hm and fz, the following formula could be used if ae/DC < 30%. 730
Download PDF file
Table of contents
Build your own flipbook