Page number 2

SECTION E-1 Rev. 2-17 TAPPING SLEEVES & CROSSES UL / FM FIRE PROTECTION PRODUCTS Mueller tapping sleeves, cut-in sleeves and crosses meet applicable AWWA Standards. Currently, there are no UL listings nor standards for these products. H-619 Mechanical Joint Tapping Sleeve with Duck Tipped End Gaskets. • Maximum Working Pressure: 200 psig (1375 kPa/ 14 barg) • Suitable for use with Asbestos-Cement Pipe in the following O.D. Range. Nominal Main Size 4" O.D. 6" O.D. 8" O.D. 10" O.D. 12" O.D. Range 4.97"-5.57" 7.05"-7.60" 9.22"-9.79" 11.77"-12.25" 14.03"-14.51" Sizes* 4"x4" 6"x4" / 6"x6" 8"x4" / 8"x6" / 8"x8" 10"x4" / 10"x6" / 10"x8" / 10"x10" 12"x4" / 12"x6" / 12"x8" / 12"x10" / 12"x12" IMPORTANT – Actual diameter of AC Pipe varies between manufacturers and from piece to piece, therefore, it is important to measure the pipe diameter to insure proper fit of these sleeves–especially in the 4", 6", and 8" sizes. Out-of-round AC Pipe can often be reduced. All such work should be done in compliance with Pipe Manufacturers' Recommendations. *First number is size of Main, second is size of the side outlet of Sleeve or Cross. H-615 4"-24" - Mechanical Joint Tapping Sleeve with Duck Tipped End Gaskets. • H-615 maximum working pressure 4"-12" main sizes - 250 psig (1725 kPa/17 barg) H-616 10"-24" - Mechanical Joint Tapping Sleeve with Plain Rubber End Gaskets. • H-616 maximum working pressure 10"-24" main sizes - 200 psig (1375 kPa/14 barg) H-715 4"-24" - Mechanical Joint Tapping Cross with Duck Tipped End Gaskets. • H-715 maximum working pressure 4"-12" main sizes - 200 psig (1375 kPa/14 barg); 14"-24" 150 psig (1100 kPa/11barg) • H-615 and H-715 are suitable for use on the following: - 4"-8" cast iron classes 100, 150, 200 & A-all classes; Ductile iron - cast iron O.D. PVC plastic pipe classes 150 & 200 or cast iron classes B, C, & D - A-C classes 100 & 150. Please specify pipe type when ordering. - 10"-12" cast iron classes 150, 200, 250, A & B - all classes ductile iron - cast iron O.D.PVC plastic pipe classes 150 & 200 - 14"-24" cast iron classes 50, 100, 150, 200, 250, A & B - all classes ductile iron H-616 is suitable for use on AWWA Classes C & D cast iron pipe and ANSI classes 150-250 cast iron pipe, the 4" and 6" sizes are also suitable for use with AWWA class B cast iron pipe. Sizes*: 4"x4", 6"x4", 6"x6", 8"x4", 8"x6", 8"x8", 10"x4", 10"x6", 10"x8", 10"x10", 12"x4", 12"x6", 12"x8", 12"x10", 12"x12", 14"x14", 16"x4", 16"x6", 16"x8", 16"x10", 16"x12", 16x14", 18"x4", 18"x6", 18"x8", 18"x10", 18"x12", 20"x4", 20"x6", 20"x8", 20"x10", 20"x12", 20"x14", 24"x4", 24"x6", 24"x8", 24"x10", 24"x12", 24"x14" NOTE H-615 and H-616 (H-715) described above are the same except for the end gaskets. One mechanical joint sleeve of a nominal size with two sets of end gaskets will fit all classes of pipe listed. If there is any question as to the class of pipe with which the sleeve is to be used, we recommend ordering and stocking both sets of end gaskets for each sleeve. *The first number is size of main, second is size of side outlet of sleeve. ORDERING INSTRUCTIONS FOR TAPPING SLEEVES Specify: Quantity, Nominal Size of Main, Type and Class of Main, Circumference or O.D. of Main, Size of Outlet, and Catalog Number. CAUTION ASBESTOS AND OTHER MATERIALS MAY CAUSE CANCER CAUSES DAMAGE TO LUNGS DO NOT BREATHE DUST AVOID CREATING DUST. Seek Expert Advice For Breathing Protection And Protective Equipment. Call OSHA 1-800-321-6742 for more information. Page E-1-2

Page number 3

UL / FM FIRE PROTECTION PRODUCTS TAPPING SLEEVES & CROSSES SECTION E-1 Rev. 2-17 T-28 Dual Compression Seal Tapping Sleeve • Fits all classes of pipe through Class D pit cast gray iron. • Test plug standard. • Epoxy coated ductile iron construction. • O-ring sealed outlet and flange connection. • Outlet flange with dimensions and drilling that comply with ANSI B16.1, Class 125 with MSS SP-60. • Stainless steel bolts. • Maximum working pressure: 250 psig (1724 kPa), Sizes*: 6"x3", 6"x4", 6"x6", 8"x3", 8"x4", 8"x6", 8"x8", 10"x3", 10"x4", 10"x6", 10"x8", 10"x10", 12"x3", 12"x4", 12"x6", 12"x8", 12"x10", 12"x12", 16"x3", 16"x4", 16"x6", 16"x8", 16"x8", 16"x10", 16"x12" *The first number is size of main, second is size of side outlet of sleeve. Tapping Sleeve pipe information Nominal size of main 6" 8" 10" 12" 16" Inch 6.90 - 7.10 9.05 - 9.30 11.10 - 11.40 13.20 - 13.50 17.40 - 17.80 O.D. Range mm 175.26 - 180.34 229.87 - 236.22 281.94 - 289.56 335.28 - 342.90 441.96 - 452.12 Class and type of pipe Fits all classes of pipe through Class D pit cast gray iron. CAUTION ASBESTOS AND OTHER MATERIALS MAY CAUSE CANCER CAUSES DAMAGE TO LUNGS DO NOT BREATHE DUST AVOID CREATING DUST. Seek Expert Advice For Breathing Protection And Protective Equipment. Call OSHA 1-800-321-6742 for more information. Page E-1-3

    ...