Page number 8

5.8 Rev. 12-15 Shaded area indicates change MUELLER® SINGLE SECTION FULL-SEAL® PIPE REPAIR CLAMPS 500 Series Single Section Full-Seal® Pipe Repair Clamps — for 2" through 12" cast iron , ductile iron , steel, A-C and PVC pipe. Standard Lengths: 6", 7-1/2", 9", 10", 12", 15", 18", 20", 24", 30" Nominal Pipe Size 2" 2-1/2" 3" 3" 3" 3-1/2" 4" 4" 4" 4" 6" 6" 6" 6" 6" 6" 6" 8" 8" 8" 8" 8" 8" 10" 10" 10" 10" 10" 10" 12" 12" 12" 12" 12" 12" 12" Clamp size - number 235 270 297 346 373 396 445 474 495 520 566 594 634 655 684 704 722 792 836 853 899 925 940 990 1040 1064 1104 1137 1175 1200 1220 1246 1260 1314 1356 1400 Clamp O.D. range* Inches Millimeters Min. Max Min. Max 2.35 2.63 59.7 66.8 2.70 2.98 68.6 75.7 2.97 3.25 75.5 82.5 3.46 3.72 87.9 94.4 3.73 4.00 94.8 101.6 3.96 4.25 100.6 107.9 4.45 4.87 113.1 123.6 4.74 5.14 120.4 130.5 4.95 5.35 125.8 135.8 5.20 5.60 132.1 142.2 5.66 5.91 143.7 150.1 5.94 6.34 150.9 161.0 6.34 6.74 163.3 171.2 6.55 6.97 164.4 177.0 6.84 7.24 173.8 183.8 7.04 7.44 178.9 188.9 7.22 7.62 183.4 193.5 7.92 8.32 201.1 211.3 8.36 8.76 212.3 222.2 8.53 8.93 216.7 226.8 8.99 9.39 228.4 238.5 9.25 9.65 235.0 245.1 9.40 9.80 238.8 248.9 9.90 10.30 251.4 261.6 10.40 10.80 264.1 274.3 10.64 11.04 270.3 280.4 11.04 11.46 280.5 291.0 11.37 11.77 288.8 298.9 11.75 12.15 298.5 308.6 12.00 12.40 304.8 315.0 12.20 12.60 309.9 320.0 12.46 12.86 316.5 326.6 12.60 13.00 320.1 330.2 13.14 13.56 338.8 344.4 13.56 13.96 344.5 354.5 14.00 14.40 355.7 365.7 Cast Iron 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250, A 50-250,A,B,C,D 50-250, A 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D Ductile Iron All All All All All All All All All All Cast Iron O.D. PVC Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Steel*** 2" 2-1/2" 3" O.D. 3" 3-1/2" (4" O.D.) STD 6" O.D. STD STD 8" O.D. STD 10" O.D. STD 12" O.D. STD 14" A-C Rough Barrel Class100**,150 Class100**.150 Class 150, 200 Class100**,150 Class 200 Class100**,150 Class 200 Class100** Class 100, 150 Class100** Class 150, 200 * Verify pipe O.D. before selecting clamp size. ** CAUTION—O.D. of class 100 A-C pipe varies greatly. Measure pipe O.D. to assure proper clamp selection. ***Also fits PVC Plastic Pipe - ASTM D2241 SDR 17 and lower and ASTM D1785 schedule 80 and above. Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. WARNING: Use on A-C pipe, which contains a known carcinogen, requires appropriate protective equipment and procedures be employed.

Page number 9

MUELLER® SINGLE SECTION SERVI-SEAL® PIPE REPAIR CLAMPS Typical Single Section Servi-Seal Clamp Shaded area indicates change Rev. 9-09 5.9 Single Section Servi-Seal Pipe Repair Clamps - with integral 3/4" through 2" IP/CC Threaded service outlet - for 2" through 12" cast iron, ductile iron, steel pipe, A-C and PVC pipe. 1.Stylenumber—501-509(seechartbelow) 2.Length—Standardlengthavailable(inches):5,6,7-1/2(listas“7”),9,12,15,18,20,24,30 3.Sizenumber—fromchartonpage15.10 4.Catalognumberprefixorsufixforoptionalfeatures,ifdesired. ThecatalognumberforaSingleSectionServi-SealRepairClampwith3/4"IPoutlet,12" long for 8" cast iron pipe is 501-12-899. To specify the catalog number, provide the following information: Style number 501-509 Clamp style number 501 Clamp length 12 Size/type of outlet tapping thread 3/4"IP 3/4" CC 1"IP 1" CC 1-1/4"IP 1-1/2" CC 1-1/2"IP 2"CC 2"IP Clamp size number 899 Sizes available* 2.35-14.00 2.35-14.00 2.35-14.00 2.35-14.00 4.45-14.00 4.45-14.00 4.45-14.00 4.45-14.00 4.45-14.00 Clamp style number Starter nut Style number 501 502 503 504 505 506 507 508 509 Standard bolt & nut 510 Series nuts and bolts *Clamps available to fit specific size pipe within this nominal size range. Extra bolts and nuts for Mueller Single Section Servi-Seal Repair Clamps Clamp size 2"-3-1/2" 4"-12" (standard bolt and nut) 4"-12" (starter bolt and nut) Bolt size 1/2"-6" 5/8"x6" 5/8x7" Bolt part number 521009 521008 524308 Nut part number 521010 195236 526655 Bonding device NOTE: 4" and larger 500 Series Clamps are provided with one starter bolt/nut per side as standard. Stainless steel bolts Foroptional304stainlesssteelbolts,washersandnuts,add“S-”prefixtoclampcatalognumber. Example: S-501-12-899. Deep socket wrenchs Bonding device SpeciallydesignedforusewithMuellerFull-SealRepairClamps.Long ratchet handle has thumb- tip reverse. Deep sockets (3-1/4") have double hex (12 pt.) and 1/2" square drive. Part number 515204 520344 515207 519575 Description 15-3/4" with reversible ratchet handle 7/8" socket for 2" through 3-1/2" clamps 1-1/16" socket for 4" and larger clamps 1/2"x3/4" adapter Bonding device for cathodic protection Metallicconductorsaresetinthegaskettoprovidecontactbetweenthebandandthepipesurfaceandareavailableonall500seriesclamps.Theseconductorspermitelectricalcurrentflow by establishing positive contact with pipe and band on each side of the pipe crack or break. To specify optional bonding deviceforcathodicprotection,addaprefixof“2”tocatalognumber. Example: 2-501-12-899. Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. IMPORTANT: PIPE REPAIR CLAMPS have demonstrated their capability to seal against water pressures commonly encountered in distribution systems. Smaller diameter clamps of a given design can seal against higher pressures than larger ones. In addition, the pressure that a clamp can contain is effected by the torque applied to the bolts, the uniformity of bolt tightening (when there is more than one bolt), as well as the type and extent of pipe damage, surface condition of the pipe, environmental conditions, and installation workmanship. WARNING: Use on A-C pipe, which contains a known carcinogen, requires appropriate protective equipment and procedures be employed.

    ...