Page number 4

5.4 Rev. 9-09 Shaded area indicates change MUELLER® 200 SERIES PIPE-SAVER® REPAIR CLAMPS AND BELL JOINT REPAIR CLAMPS 200 Series Clamps The stainless steel 200 Series Pipe-Saver Clamp comes in3",6",9",12",and18"lengths,insinglesectiontofit 1/2"-8"standardsteelpipe,andintwosectionstofit 10" - 24" standard steel pipe. Cemented-in gaskets are available with a choice of smooth or gridded surfaces. A clamp is also available with a separate cone gasket tocloseholesordeeppits.Highcarbonsteelboltswith corrosion-resistant plating are standard; stainless steel bolts optional. The stainless steel 200 Series Pipe-Saver Clamp ❏ Repairholes ❏ Repairsplits ❏ Heavyboltshoulderspreventturninginlug. ❏ Steelbolthasrolled,spin-fitthreadstospeed installation. ❏ Heavy,hexnutprovidesmorethreadcontactfor greater strength. ❏ Type304Lstainlesssteelband ❏ Ductileironlugsareshapedtoprovideuniform clamping pressure on pipe. ❏ Maximumwaterworkingpressureforproperly installed clamps with nuts tightened to 500 inchpoundstorque*:1/2"-4"350psig(2400kPa/24barg); 6"-8" 200 psig (1375 kPa/14 barg); 10"-12" 150 psig; 14"-16" 100 psig (700 kPa/7 barg), 18" - 24" 60 psig (425 kPa/4 barg). *IMPORTANT: PIPE REPAIR CLAMPS have demonstrated their capability to seal against water pressures commonly encountered in distribution systems. Smaller diameter clamps of a given design can seal against higher pressures than larger ones. In addition, the pressure that a clamp can contain is effected by the torque applied to the bolts, the uniformity of bolt tightening (when there is more than one bolt), as well as the type and extent of pipe damage, surface condition of the pipe, environmental conditions, and installation workmanship.

Page number 5

MUELLER® 200 SERIES PIPE-SAVER® PIPE REPAIR CLAMPS Typical 200 Series Pipe-Saver Clamps Shaded area indicates change Rev. 9-09 5.5 200 Series Pipe-Saver Pipe Repair Clamps - for 1/2" through 24" standard steel pipe To specify the catalog number, use the charts to select the following information for the desired clamp: 1. Style number 2. Length 3. Size number *Clamps available to fit specific size standard steel pipe within this nominal size range. The catalog number for a 220 Style Clamp, 3" long for 1-1/2" steel pipe is 220-3-190 220 Clamp style number 220 Clamp length 3 Clamp size number 190 Clamp style number Bolts Style number 210 211 212 213 218 219 220 221 Type of gasket Smooth† Smooth† Gridded Gridded Smooth† Smooth† Gridded Gridded Gasket coverage Full Full Full Full Regular Regular Regular Regular Corrosion resistive plating X X X X Stainless steel X X X X Size available* 1/2"-24" 1/2"-24" 1/2"-24" 1/2"-24" 1-1/2"-24" 1-1/2"-24" 1-1/2"-24" 1-1/2"-24" 218 †Smooth gasket material is reinforced for 1-1/2" - 24" sizes Clamp length and clamp style number Standard steel pipe size†† 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 5" 6" 8" 10" 12" 14" Clamp size number 0084 0105 0131 0166 0190 0237 0287 0350 0400 0450 0556 0662 0862 1075 1275 1400 1600 1800 2000 2400 Standard steel pipe O.D. 0.840 1.050 1.315 1.660 1.900 2.375 2.875 3.500 4.000 4.500 5.563 6.625 8.625 10.750 12.750 14.000 16.000 18.000 20.000 24.000 Number of clamp sections Clamp lengths available 3" 6" 9" 12" 18" Clamp lengths available 3" 6" 9" 12" 15" 18" Number of bolts 1 2 3 4 6 Number of bolts 2 4 6 8 10 12 221 1 213 16" 18" 20" 24" †† Nominal Sizes 2 *IMPORTANT: PIPE REPAIR CLAMPS have demonstrated their capability to seal against water pressures commonly encountered in distribution systems. Smaller diameter clamps of a given design can seal against higher pressures than larger ones. In addition, the pressure that a clamp can contain is effected by the torque applied to the bolts, the uniformity of bolt tightening (when there is more than one bolt), as well as the type and extent of pipe damage, surface condition of the pipe, environmental conditions, and installation workmanship

    ...