Page number 16

5.16 Rev. 2-11 Shaded area indicates change MUELLER® SINGLE SECTION FULL-SEAL® ALL STAINLESS STEEL PIPE REPAIR CLAMPS 540 Series Single Section Full-Seal® All Stainless Steel Pipe Repair Clamps — for 2" through 12" cast iron, ductile iron , steel, A-C and PVC pipe. Standard Lengths: 7-1/2", 10", 12-1/2", 15", 20", 30" Nominal Pipe Size 2" 2-1/2" 3" 3" 3" 3-1/2" 4" 4" 4" 4" 6" 6" 6" 6" 6" 8" 8" 8" 8" 10" 10" 10" 10" 10" 12" 12" 12" 12" 12" Clamp size - number 235 270 297 345 373 395 445 474 495 522 595 656 684 705 740 795 854 899 927 970 1070 1104 1140 1175 1200 1262 1310 1340 1400 Clamp O.D. range* Inches Millimeters Min. Max Min. Max 2.35 2.63 59.7 66.8 2.70 3.00 68.6 76.2 2.97 3.25 75.5 82.5 3.45 3.72 87.9 94.4 3.73 4.00 94.8 101.6 3.95 4.45 4.74 4.95 5.22 5.95 6.56 6.84 7.05 7.40 7.95 8.54 8.99 9.27 9.70 10.70 11.04 11.40 11.75 12.00 12.62 13.10 13.40 14.00 4.25 4.87 5.14 5.35 5.62 6.35 6.96 7.24 7.45 7.80 8.35 8.94 9.39 9.67 10.10 11.10 11.44 11.80 12.15 12.40 13.02 13.50 13.80 14.40 100.3 113.1 120.4 125.8 132.6 151.1 166.6 173.8 179.1 188.0 201.9 216.9 228.4 235.5 246.4 271.8 280.5 289.6 298.5 304.8 320.5 332.7 340.4 355.7 107.9 123.6 130.5 135.8 142.7 161.3 176.8 183.8 189.2 198.1 212.1 227.1 238.5 245.6 256.5 281.9 290.6 299.7 308.6 315.0 330.7 342.9 350.5 365.7 Cast Iron 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250, A 50-250,A,B,C,D 50-250, A 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D Ductile Iron All All All All All All All All All All Cast Iron O.D. PVC Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Steel*** 2" 2-1/2" 3" O.D. 3" 3-1/2" (4" O.D.) STD 5" O.D. 6" O.D. STD STD 10" O.D. STD STD A-C Rough Barrel Class100**,150 Class100**,150 Class 150, 200 Class100**,150 Class 200 Class100**,150 Class 200 Class100** Class 150, 200 Class100** Class 150, 200 *Verify pipe O.D. before selecting clamp size. **CAUTION—O.D. of class 100 A-C pipe varies greatly. Measure pipe O.D. to assure proper clamp selection. ***Also fits PVC Plastic Pipe - ASTM D2241 SDR 17 and lower and ASTM D1785 schedule 80 and above. Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. WARNING: Use on A-C pipe, which contains a known carcinogen, requires appropriate protective equipment and procedures be employed.

Page number 17

MUELLER® SINGLE SECTION SERVI-SEAL® ALL STAINLESS STEEL PIPE REPAIR CLAMPS Typical Single Section Servi-Seal Clamp Shaded area indicates change Rev. 9-09 5.17 541 - 549 Series Single Section Servi-Seal All Stainless Steel Pipe Repair Clamps - with integral 3/4" through 2" IP/CC Threaded service outlet-for 2" through 12" cast iron, ductile iron, steel pipe, A-C and PVC pipe. To specify the catalog number, provide the following information : 1.Stylenumber—541-549 (see chart below) 2.Length—Standard length available (inches): 7-1/2 (list as “7”), 10, 12-1/2, 15, 20, 30 3. Size number—from chart on page 15.18 4.Catalognumberprefixorsufixforoptionalfeatures,ifdesired. ThecatalognumberforaSingleSectionServi-SealRepairClampwith3/4"IPoutlet,12"clamp length for 8" cast iron pipe is 541-12-899. Style number 541-549 Clamp style number 541 Clamp length 12 Size/type of outlet tapping thread 3/4"IP 3/4" CC 1"IP 1" CC 1-1/4"IP 1-1/2" CC 1-1/2"IP 2"CC 2"IP Clamp size number 899 Sizes available* 2.35-14.40 2.35-14.40 2.35-14.40 2.35-14.40 4.45-14.00 4.45-14.00 4.45-14.00 4.45-14.00 4.45-14.00 Clamp style number Style number 541 542 543 544 545 546 547 548 549 541-549 Series nut and washer *Clamps available to fit specific size pipe within this nominal range. Bonding device Extra Nuts and Washers for Mueller Single Section Full Seal All Stainless Repair Clamps Clamp size 4"-12" (standard nut) Bolt size 5/8" Bolt part number 311581 Nut part number 311582 *Clampsavailabletofitspecificsizepipewithinthisnominalsizerange. Deep socket wrenchs SpeciallydesignedforusewithMuellerFull-SealRepairClamps.Long ratchet handle has thumb- tip reverse. Deep sockets (3-1/4") have double hex (12 pt.) and 1/2" square drive. Part number 515204 515207 Description 15-3/4" with reversible ratchet handle 1-1/16" socket for 4" and larger clamps Bonding device Bonding device for cathodic protection Metallicconductorsaresetinthegaskettoprovidecontactbetweenthebandandthepipe surface and are available on all 500 series clamps. These conductors permit electrical current flowbyestablishingpositivecontactwithpipeandbandoneachsideofthepipecrackorbreak. To specify optional bonding deviceforcathodicprotection,addaprefixof“2”tocatalognumber. Example: 2-541-12-899. Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. IMPORTANT: PIPE REPAIR CLAMPS have demonstrated their capability to seal against water pressures commonly encountered in distribution systems. Smaller diameter clamps of a given design can seal against higher pressures than larger ones. In addition, the pressure that a clamp can contain depends upon the torque applied to the bolts, the uniformity of bolt tightening (when there is more than one bolt), as well as the type and extent of pipe damage, surface condition of the pipe, environ- mental conditions, and installation workmanship. WARNING: Use on A-C pipe, which contains a known carcinogen, requires appropriate protective equipment and procedures be employed.

    ...