Page number 20

MUELLER ® SHUR STOP ™ SERVICE VALVES Rev. 8-17 Shaded area indicates changes 14.2 0 Mueller Shur Stop FIP x FIP Non-directional flow; for Natural or LP gases; meets test requirements specified in ANSI B16.33; optional test taps at inlet and/or outlet; 175 psig (1208 kPa). Body: Size: Weight (each): Catalog Numbers 805002 805006 Black Black 3/4" 1" 2.9 lbs. 3.5 lbs. Mueller Shur Stop FIP x Wedgeseal ™ Insulated Union† Non-directional flow; for Natural or LP gases; meets test requirements speci - fied in ANSI B16.33; optional test taps at inlet and/or outlet; 175 psig (1208 kPa). Body: Pipe size: Weight (each): Catalog Numbers 805000 Black 3/4" FIP x 3/4" FIP 3.6 lbs. 805010 Black 3/4" FIP x 3/4" MIP 3.6 lbs. Replacement Parts 805000 Tailpiece/union 071197-5 Coupling nut - black 017814-1 Union o-ring 015294 805010 015947-5 017814-1 015294 Steel Dome Locking Device The LOK-DOME ™ locking device is made of hardened steel, with a zinc plated yellow chromate treatment. It fits over the Shur Stop valve head, shielding it from hammering, sawing or prying. One size fits both 3/4" and 1" Shur Stop valves. A two piece barrel locking pin is available that can be used with or without the LOK-DOME cap to lock-off Shur Stop valves. A special key is used to lock and unlock the device. 507049 Locking Pin 504980 - Key 71152 LOK-DOME Cap * Includes an 1/8" steel recessed hex head pipe plug on side at inlet. † Tailpiece of Wedgeseal insulated union is brass. A 3/4" female NPT tailpiece is available in zinc plated steel. ++ Available in minimum quanities. Contact Customer Service for availability.

Page number 21

14.2 1 H-11199 H-853 H-11199 Relubricating Tool used to relubricate Mueller Luboseal ® and Brisco ™ Meter Valves with H-853 lubricant shown below. A hex wrench is built into the tool handle for removal of valve lubricating port pipe plug. One tool fits all valve sizes. Replacement Parts: 304609 O-ring 505425 Teflon Backup Ring H-853 Ground Key Lubricant Used for dry natural or manufactured gas, air and vacuum applications. NOT recommended for petroleum solvents, mineral oils or concentrated acids or alkalies. Box of 24 #1 sticks. OPTIONAL EQUIPMENT Shaded area indicates change Rev. 6-10 (valve not included) Steel Yoke Locking Device Can be used on the following 3/4" and 1" plain head Mueller ® Gas meter valves (or meter valves of equivalent dimensions) to lock them in the closed position: H-11170, H-11174, H-11116, and H-11126. This device consists of a case hardened steel yoke that fits over the closed meter valve, a two piece parrel locking pinthat secures the yoke to the valve, and a special key is used to lock and unlock the device. The yoke fits both 3/4" and 1" valves. Yoke only: 507050 Barrel Locking pin only: 507049 Key only: 504980 *H-11094 includes 507050 & 507049 (stop not included) H-11090 H-11091 H-11090 Lock wing sealing device Is used with lock wings drilled 1/2". This device consists of two parts; collar and screw (H-11091) and a 15/32" O.D. pin (H-11092). This device is used to detect unauthorized use. H-11093 (valve not included) Part name Yoke Locking pin Key Iron Yoke Locking Device Provides a method of locking the following plain head Mueller Gas meter valves (or meter valves of equivalent dimensions): H-11170, H-11174, H-11116, and H-11126. This device consists of an iron yoke that fits over the inlet hex and the key head of the closed valve, and a two piece barrel locking pin that secures the yoke to the valve body. A special key is required to operate the lock. 3/4" 504976 504978 504980 Size 1" 504977 50497 8 504980 H-11092

    ...