QUICK GUIDE Motorstyring / Motor Controller Type TR-EM-273 Parameterindstillinger / Parameter settings Tilslut programmeringsenheden TR-EM-236 og indlæs nedenstående værdierne for det pågældende aktuatorsæt Pa ra meter FB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 DIP LA12 Reed 2 1 0 100 100 75 30 30 5 1 1 2 10 20 2 10 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA14 Ha l l -pot 0 1 1 100 100 75 30 30 5 1 1 1 10 20 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA20/25 Ha l l 0 1 0 100 100 100 60 60 5 2 2 2 10 30 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA23 Ha l l 0 1 0 100 100 75 30 30 5 1 1 1 10 20 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA25 Ha l l -pot 0 1 4 100 100 100 60 60 5 2 2 2 10 30 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA28/30/32 Reed 0 1 0 100 100 75 60 60 5 1 3 2 10 30 2 20 10 1 1 1 1 0 3 0 255 10 5 Learn Vcc Vcc-6V 5V LP2 Reed 0 1 0 100 100 75 10 60 5 1 3 2 10 30 2 20 10 1 1 1 1 1 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA31 Reed 2 1 0 100 100 75 60 60 5 1 3 3 10 20 2 10 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA33 Ha l l -pot 0 1 2 100 100 100 60 60 5 2 9 9 10 30 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA35 Ha l l 0 1 0 100 100 75 60 60 1 1 5 5 10 30 2 10 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA36 Ha l l 0 1 0 100 100 100 60 60 5 2 10 10 10 30 2 10 5-10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V LA36 Ha l l -pot 0 1 2 100 100 100 60 60 5 2 10 10 10 30 2 20 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V BL1 Ha l l 0 1 0 100 100 75 60 60 1 1 5 5 10 30 2 10 10 1 1 1 1 0 3 0 255 10 10 Learn Vcc Vcc-6V 5V Opstart i læringstilstand Starting up in Learning mode 1.Start læring ved at trykke på PIL-OP og PIL-NED på samme tid i >5 sekunder. 1.To initiate Learning mode, press ARROW UP and ARROW DOWN simultaneously for >5 seconds. 2.Vigtigt! Oprethold kommandoen, indtil læringscyklussen er helt gennemført. Dvs. indtil aktuatorerne har nået endepositionen ude og er returneret til udgangsposition. 3.Aktuatorerne starter med at køre udad (FREM) med redu- ceret hastighed. Strømgrænse eller pulstab stopper motor- en, når det mekaniske endestop er nået. 4.Aktuatorerne kører nu indad (TILBAGE) i hele slag- længden. 5.Når aktuatorerne når til det mekaniske endestop, holdes knapperne nede i yderligere 10 sek. 6.Den lærte fulde slaglængde måles og gemmes som et værdi område på 0-1023 (Parameter 28). systemet er nu klar til brug. For yderligere vejledning, henvises til brugsanvisningen på http://www.linakthirdparty.com/ 2.Important! Maintain the command until the entire learning cycle has been completed – i.e. until the actuators have reached their end position (out) and returned to their starting position (in). 3.The actuators start by moving out (FORWARD) at reduced speed. The power limit or pulse loss will stop the motor once the mechanical end stop has been reached. 4.The actuators will then move in (BACK) along the full stroke length. The pulse counter will measure the area long the full stroke length. 5.When the actuators reach the mechanical end stop, keep the buttons pushed for at least 10 sec. more. 6.The full stroke length learned is then measured and saved with a value range of 0–1023 (Parameter 28). The system is now ready for use. For detailed instructions please refer to the Instruction manual at http://www.linakthirdparty.com/ Specifikationerne kan ændre sig uden forudgående varsel. Det er brugerens ansvar at fastslå LINAK produktets egnethed til en specifik applikation. LINAK vil ved levering ombytte/reparere defekte produkter, som er dækket af garanti, hvis de straks returneres til LINAK Danmark A/S. Der påtages intet ansvar udover denne ombytning/reparation. Specifications subject to change without prior notice. It is the responsibility of the product user to determine the suitability of the products for a specific application. LINAK Danmark will at point of delivery replace/repair defective products covered by the warranty if promptly returned to LINAK Danmark. No liability is assumed beyond such replacement/repair. Produceret af / Produced by Electromen OY Forhandler / Distributor: LINAK Danmark A/S Mønstedsvej 9 DK-8600 Silkeborg Tlf. +45 86803611 - www.linak.dk
Download PDF file