FlowCon Green.3 1B95091 - 09/2023 Nominal flow rate FlowCon International assumes no responsibility for mistakes, if any, in any printed material. Setting and Installation Prior to installing the FlowCon Green.3 (supplied from factory in setting 4.5 due to calibration), the system should be properly flushed. If it is not possible to flush the system before Green.3 in- stallation, please make sure to adjust setting to 5.0 (clockwise turning) and then flush. The desired flow rate is hereafter set by adjust- ing the valve (turn counter-clockwise to setting 1.0 and then clockwise up) with a special adjust- ment key (i.e. figure 3/4). Range is between 1.0 and 5.0. ⚠ Do not overturn. Scale setting is located on top of the valve numbered 1 to 5 in- cluding in-between positions indicated by dots (one dot for every 0.1 position). The specific po- sition is defined by an indication mark on top of the housing. Once flow is set, the required actua- tor may be applied. Please see specific installa- tion instruction for selected actuator. Figure 3 A micrometer setting of 3.4 as illustrated in figure 4 corresponds to a maximum flow rate of: 2.86 l/sec (45.4 GPM). Turn to higher settings Figure 4 Turn to setting 1.0 FlowCon Green.3 16-800 kPaD · 2.3-116 psid 1 Setting l/sec l/hr GPM 0.528 1900 8.36 1.0 0.633 2280 10.0 1.1 0.738 2660 11.7 1.2 0.843 3030 13.3 1.3 0.947 3410 15.0 1.4 1.05 3790 16.7 1.5 1.16 4160 18.3 1.6 1.26 4540 20.0 1.7 1.36 4910 21.6 1.8 1.47 5280 23.2 1.9 1.57 5650 24.8 2.0 1.67 6010 26.4 2.1 1.77 6370 28.0 2.2 1.87 6730 29.6 2.3 1.97 7080 31.2 2.4 2.06 7430 32.7 2.5 2.16 7780 34.2 2.6 2.25 8120 35.7 2.7 2.35 8450 37.2 2.8 2.44 8780 38.6 2.9 2.53 9100 40.0 3.0 2.61 9410 41.4 3.1 2.70 9720 42.8 3.2 2.78 10000 44.1 3.3 2.86 10300 45.4 3.4 2.94 10600 46.6 3.5 3.02 10900 47.8 3.6 3.10 11100 49.0 3.7 3.17 11400 50.2 3.8 3.24 11600 51.3 3.9 3.30 11900 52.3 4.0 3.37 12100 53.3 4.1 3.43 12300 54.3 4.2 3.48 12500 55.2 4.3 3.54 12700 56.0 4.4 3.59 12900 56.8 4.5 3.64 13100 57.6 4.6 3.68 13200 58.3 4.7 3.72 13400 58.9 4.8 3.76 13500 59.5 4.9 3.79 13600 60.0 5.0 Accuracy: Greatest of either ±10% of controlled flow rate or ±5% of maximum flow rate. Note 1: If used in pressure range 400-800 kPaD (58-116 psid), accuracy of -20% / +0% applies. This paper is a supplement to the FlowCon General Instruction Latest release of any FlowCon material is available on www.flowcon.com Page 2 of 2
Download PDF file