Page number 4
FlowCon SM DN15-250 (1/2”-10”) 11/2024 Programming Menu The programming menu is always accessible. To enter the program- ming menu, simultaneously press and for 6 seconds, until bottom line in display blinks. To change a value, press or . For quick scroll through values hold down or . Press to accept a value and go to next step and press to go to previous step. For fast menu exit press and simultaneously for 6 seconds. The actuator will automatically return to normal operation mode if no action is detected on arrow keys for 1 minute. All values selected in the programming menu are stored in non-volatile memory. Step Display Description Values 0 * Password. *scrolling top: ENTER PASS WORD Disabled by default Password: 3569266. Only if Enabled (in step 11). Change one digit at a time, press and to move between digits. At last digit, press to go to next step. 1 * Select language. *scrolling top: SELECT LANGUAG Default: English. Possibility to choose other languages later on (not currently an option). 2 * 3 * Select valve model onto which the actuator is installed. *scrolling top: SELECT VALVE MODEL Choose unit scale for flow rate. *scrolling top: SELECT UNIT SCALE Default: SM.0.0. Select from the 11 available valve models starting from SM.1.1 Options: SM.1.1, SM.2.1, SM. Default: l/sec. Options: l/sec or l/hr or GPM. 4 * 5 * Activate Flush mode at start-up. *scrolling top: SELECT FLUSH MODE Select type of control signal. *scrolling top: SELECT CONTROL SIGNAL Default: Enable. Options: Enable or Disable. When no control signal (analog) is detected at start up, flush mode is started (5/6 of fully opened). It will be dismissed when control signal is detected. Default: 2-10VDC. Options: • 2-10VDC for VDC • 4-20mA for mA • Digital for 2 position or 3 point floating. • BACnet ( Only valid for SM.0.0.0.6). This paper is a supplement to the FlowCon General Instruction Latest release of any FlowCon material is available on www.flowcon.com Page 4 of 8
Page number 5
FlowCon SM DN15-250 (1/2”-10”) 11/2024 Step Display 6 * 7 * 8 * 9 * 10 * rotatio NC Description Select minimum control value. *scrolling top: SET MINIMUM LIMIT Select maximum control value. *scrolling top: SET MAXIMUM LIMIT Values Volt default: 2. Options: from 0-7. Increment: 0.1. mA default: 4. Options: from 0-14. Increment: 0.2. NA if Digital (in step 5). Volt default: 10. Options: from 3-10 and at least 3 VDC greater than the selected minimum limit. Increment: 0.1. mA default: 20. Options: from 6-20 and at least 6 mA greater than the selected minimum limit. Increment: 0.2. NA if Digital (in step 5). Select feedback signal. *scrolling top: SELECT FEEDBAC SIGNAL Set the designed maximum flow. Accuracy: Greatest of either ±5% of de- signed max. flow or ±2% of max. valve flow. *scrolling top: SELECT MAXIMUM FLOW Default: AU; Automatic match of control signal if analog. Options: 0-10 VDC, 2-10 VDC or 4-20 mA or AU. If Digital (in step 5) AU is not an option. Default: Maximum setting. Values depend on valve model and unit scale chosen in step 2 and 3. Stepping increments as per tech note. Select direction of rotation. *scrolling top: SELECT ROTAT DIRECT Default: Normally Closed (NC). Options: Normally Open (NO) or Nor- mally Closed (NC). 11 * 12 * Select actuator mode. *scrolling top: actuator mode Activation of password. *scrolling top: ACTIVAT PASS WORD Default: Linear flow. Options: Linear flow, Equal percentage, Linear rotation or Linear signal. For SM.1 and SM.2 only linear flow and linear rotation will apply. Default: Disable. Options: Enable or Disable. If Enabled password is required to ac- cess alarm and programming menu. 13 * failsaf close Select direction of rotation when Failsafe. *scrolling top: SELECT FAIL SAFE DIRECT Default: Close. Options: Open or Close. Only valid for SM.0.0.0.4/6 (failsafe models). Failsafe direction open means opening to max. flow chosen in step 9. This paper is a supplement to the FlowCon General Instruction Latest release of any FlowCon material is available on www.flowcon.com Page 5 of 8
