Page number 22

5.22 Rev. 9-09 Shaded area indicates change MUELLER® XTRA-RANGE® SERVI-SEAL® ALL STAINLESS STEEL PIPE REPAIR CLAMPS 551-559 Series Xtra-Range Servi-Seal All Stainless Steel Pipe Repair Clamps — for 3" through 12" cast iron, ductile iron , A-C and PVC plastic pipe. Standard Lengths: 7-1/2", 10", 12-1/2", 15", 20", 30" Nominal Pipe Size 3" 4" 4" 6" 6" 8" 8" 10" 10" 10" 12" 12" 12" 12" Clamp size - number 349 444 474 662 684 862 899 1075 1110 1160 1275 1320 1365 1400 Clamp O.D. range* Inches Millimeters Min. Max Min. Max 3.49 4.29 88.6 109.0 4.44 5.24 112.8 133.1 4.74 5.57 120.4 141.5 6.62 7.42 168.1 188.5 6.84 7.64 173.7 194.7 8.62 9.42 218.9 293.3 8.99 9.79 228.3 248.7 10.75 11.55 273.0 293.4 11.10 11.90 281.9 302.3 11.60 12.40 294.6 315.0 12.75 13.55 323.8 344.2 13.20 14.00 335.3 355.6 13.65 14.00 14.45 14.80 346.7 355.6 367.0 375.9 Cast Iron 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D 50-250,A,B,C,D Ductile Iron All All All All All Cast Iron O.D. PVC Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Class 150, 200 Steel*** STD STD A-C Rough Barrel Class100**,150,200 Class100**,150,200 Class100**,150,200 Class100** Class 150, 200 Class100** Class100**,150,200 - *Verify pipe O.D. before selecting clamp size. **CAUTION—O.D. of class 100 A-C pipe varies greatly. Measure pipe O.D. to assure proper clamp selection. Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. WARNING: Use on A-C pipe, which contains a known carcinogen, requires appropriate protective equipment and procedures be employed.

Page number 23

MUELLER® SOLVENT WELD PVC JOINT REPAIR CLAMP Typical Solvent Weld PVC Joint Repair Clamp Shaded area indicates change Rev. 9-09 5.23 773 SeriesTM Joint Repair Clamp — for use on PE-160 PVC pipe solvent weld joints. The773seriesclamphasasteppedgasketthatfitsoverthesolventweldjointinPE-160PVC pipe to stop leaks in the joint. Catalog number 773-06-0238 773-07-0289 773-07-0350 773-07-0450 773-07-0663 733-07-0863 Nominal clamp/pipe size 2" 2-1/2" 3" 4" 6" 8" Clamp length 6" 12" 7-1/2" 12" 7-1/2" 12" 7-1/2" 12" 7-1/2" 12" 7-1/2" 12" Extra bolts and nuts for 773 series Mueller Single Section Full Seal Repair Clamps Clamp size 2"-3-1/2" 4"-12" (standard nut) Bolt size 1/2"x4-1/2" 5/8"x6" Bolt part number 521009 521008 Nut part number 521010 195236 Style number 773 NOTE: 4" and larger 773 Series Clamps are provided with one starter bolt/nut per side as standard. Stainless steel bolts Starter nut Foroptional304stainlesssteelbolts,washersandnuts,add“S-”prefixtoclampcatalognumber. Example: S-773-06-863. Deep socket wrenchs Part number 515204 520344 515207 519575 SpeciallydesignedforusewithMuellerFull-SealRepairClamps.Longratchethandlehas thumb-tip reverse. Deep sockets (3-1/4") have double hex (12 pt.) and 1/2" square drive. Standard bolt & nut 773 Series nuts and bolts Description 15-3/4" with reversible ratchet handle 7/8" socket for 2" and 3" clamps 1-1/16" socket for 4" and larger clamps 1/2"x3/4" adapter Note: For O.D. not shown contact our Customer Service Center or your Mueller Sales Representative. IMPORTANT: PIPE REPAIR CLAMPS have demonstrated their capability to seal against water pressures commonly encountered in distribution systems. Smaller diameter clamps of a given design can seal against higher pressures than larger ones. In addition, the pressure that a clamp can contain depends upon the torque applied to the bolts, the uniformity of bolt tightening (when there is more than one bolt), as well as the type and extent of pipe damage, surface condition of the pipe, environmental conditions, and installation workmanship.

    ...